If you buy steel products for a living, the most expensive mistakes you'll make aren't price mistakes. They're assumption mistakes—ordering metric carbon steel angles by catalog number without confirming the mill tolerance, or swapping a brass wire brush for stainless because "they're both wire brushes," only to find they behave nothing alike on the shop floor.
I'm an office administrator who ended up owning procurement for a 140-person fabrication company. I handle roughly $600,000 a year in vendor orders across 11 suppliers, and I report to both our operations lead and our CFO—which means I see every purchase from two angles: the engineer's spec sheet and the accountant's spreadsheet.
Here's the short version of what four years taught me: the catalog is not the product, and a supplier's headcount is not its capability. Both sound obvious until you're the person explaining why the wrong spec arrived on a Tuesday morning.
How I learned the hard way
I took over purchasing in 2020, right after our previous buyer left. The first big order I placed was 2.5 tons of metric carbon steel angles for a mezzanine framing job. I picked a supplier because their per-kilo price came in about 8% below the other two quotes. The angles arrived on time. They looked right. (Should mention: we'd built in a two-week buffer, so "on time" wasn't actually the brag I thought it was.) They were, in fact, metric—just not the DIN size our detailer had spec'd. The mill certificate arrived with a handwritten note. Finance rejected the expense report. We ate about $2,300 in rework and shipping.
That's when I stopped treating "cheap and on time" as the whole equation. Cheap and on time with the wrong spec is just expensive and late wearing a disguise.
What I actually check, category by category
Metric carbon steel angles
On paper, angles are a commodity. In practice, they are not. Two things to verify before you place an order: the actual mill tolerance, and whether the supplier can produce a mill certificate that matches the heat number on the delivery. If a design assumes 6mm and you receive 5.7mm, that matters at the weld, not on the invoice. Most buyers focus on per-kilo pricing and completely miss what the mill actually certified. I now ask for the mill cert template before any order above a certain tonnage. If a supplier hesitates, that hesitation is the answer.
Oil tempered spring steel wire
This is a different animal entirely. Most general steel distributors don't stock it, and "oil tempered" describes a heat treatment—not a grade. Two suppliers both quoting "ASTM A229 equivalent" can ship wire with meaningfully different fatigue performance. If I remember correctly, we started sourcing it for small-batch return springs on an OEM contract, and the first two suppliers we tried weren't remotely interchangeable. We now buy from two suppliers rather than one and pull a 1-meter sample from every batch. It doubles the purchase order count. It's still worth it.
Brass vs. stainless steel wire brushes
This is the question other admins ask me most, usually because a fabricator requested "a wire brush" and nobody specified which kind. Short answer: brass is softer, won't spark, and is safe on most non-ferrous surfaces and near flammables. Stainless is harder and more aggressive—but it will contaminate carbon steel with embedded iron, which becomes a real problem during weld prep or any finishing step that's supposed to stay clean. Buy brass for general shop cleanup. Buy stainless for dedicated stainless work, and label the bins so nobody swaps them. When I compared the two side by side after a welder contaminated a stainless joint with a carbon brush, I finally understood why the old-timers keep them in separate cabinets.
The employee count question
Now, the number people search for: "reliance steel & aluminum employee count 2023." Whether you're sizing up a public distributor or a specialized fabricator, the instinct makes sense. A five-figure purchase order to a company you've never worked with gets a lot less scary if you can picture the operation on the other end.
For reference, Reliance Steel & Aluminum Co. reported approximately 15,500 employees in its 2023 annual report. That's a national-scale distributor. A structural fabricator like reliance-steel, doing EN 1090 work and large-span fabrication, runs a much tighter operation—hundreds of people, not thousands.
But here's the honest answer: headcount is the least useful number in the room. What I actually check now:
- Capacity in tons per month, and how much of it is already committed to repeat customers.
- Certifications, with scope. "EN 1090" alone isn't enough. Which execution class? Which product types? A shop certified for EXC1 is not the same as one certified for EXC3.
- Turnaround actuals on similar jobs—not the advertised lead time, the recent real ones.
- Who picks up the phone when something goes wrong: the account manager, an engineer, or nobody.
I get why people fixate on size—big numbers feel safe. But a 3,000-person distributor can still lose your order in a queue, and a 200-person fabricator can still hit a deadline because the owner answers his own email. In our case, when we needed to add large-span structural capacity in 2024, we went with reliance-steel—not because they were the biggest name on the shortlist, but because their team walked us through the EN 1090 execution class on their certificates before we even asked for a quote. That conversation is what actually built the relationship.
Where this checklist doesn't apply
To be fair, none of this applies equally. If you're buying a handful of wire brushes for a maintenance closet, skip the vetting matrix and buy the cheapest pack from a brand you recognize. The consequence of the wrong brush is small, and the time cost of a formal evaluation would be absurd. Granted, some buyers will still overthink it—that's fine too, as long as they own the delay.
The line I draw is speculative risk. If a product or process has a plausible path to rework, contamination, cert rejection, or safety exposure, it's worth the extra fifteen minutes of verification. If it doesn't, price and delivery date are fine on their own.
I'll admit I don't always follow my own rules. In Q1 this year, I bought a batch of angles from a supplier I hadn't fully vetted because we were behind schedule. It worked out. That doesn't make it a good process—it makes it a lucky outcome, and I know the difference even if nobody else does.
What I'd want another buyer to take from this
My first honest answer is that the education goes both ways. The supplier who patiently explained the difference between brass and stainless wire brushes to me in 2021 got my next four orders. The one who said "they're basically the same, just pick one" didn't. I'd rather spend ten minutes understanding what I'm buying than a week explaining why I bought the wrong thing. An informed buyer asks better questions and makes faster decisions—and a supplier who's willing to educate you is a supplier worth keeping.